Twist Lock Receptacle 7 Pin IP67 Photocell Led Connectors

Quick Detail Of Waterproof Cable Connectors

The instruction covers the application requirment of ANSI C136.41-2013 dimming receptacles used for road and area lighting . All contacts are pre-installed into the receptacle housing , and pre-crimped with 30CM lead wire , with 14AWG standard wire used on three-line voltage AC circuits and 18AWG wire used in four-way signal dimming control . Ambient temperature of the application is -40 to 70 degrees , suitable for outdoor lamps which require different temperature. There are 4 dimming contacts in the receptacle assembly.

Install the on the surface of the lamp housing. It is recommended to seal the surface between the receptable components and the lamp housing to realize the water resistance. The receptacle housing has two mounting holes that can accept #8 flat-head groove screws. The appropriate length and type of screws musr be determined by the luminaire manufacturer.Depending on the type of gasket used and the type of screw installed, the installer needs to determine the torque of the mounting screw to ensure a waterproof seal between the receptacle and the lamp housing .

Wiring diagram
The receptacle lines must be connected on the line with the correct supply voltage or dimming signal source.The wiring diagram shown is for referential purposes only. The luminaire manufacturer is required to determine the wiring diagram based on the balper and driver which has dimming control components.

Stress relief
It is recommended to provide a device to secure the extended leads of the receptacle assembly to prevent excessive force being transferred from the lead to the wire/connector interface. The recommended stress relief method is to use a cable strap or fixing bracket installed inside the luminaire.

Mounting and demounting the dimming controller from the receptacle
The naught wire pins of the dimming controller is larger than the pin of the wires and load. In mounting , after correctly aligning the power pins at the receptacle power contact circuit , push down until the bottom of the dimming controller fits to the surface of the receptacle and slightly presses the gasket. Then by the twisting the dimming controller in a clockwise direction, the dimming in demounting , operate the above procedure in reverse.Qualification

The ANSI C136.41-2013 dimming receptacle is the component recognized by American insurance Laboratory in document E66375, volume 5, and has been approved by CSA international audit of UL.

Tools
Manual installation is sufficient and no special tools are required to mount the product.

Note in Mounting
Below figure shows the typical application of ANSI C1 36.41-2013 dimming receptacle.Production personnel should refer to this diagram to ensure that the product is mounted correctly.

Application Of Waterproof Cable Connectors
Electric vehicle/Power
Outdoor LED display
Outdoor LED lighting

What kind of waterproof Connector can we provide

M6 Waterproof Connector

M8 Waterproof Connector

M10 Waterproof Connector

M12 Waterproof Connector

M15 Waterproof Connector

M16 Waterproof Connector

M20 Waterproof Connector

M25 Waterproof Connector

M28 Waterproof Connector

Our Advantages

1. Customized Waterproof Connectors : For all connectors we provide OEM & ODM service.

2. Fast Delivery : 1-3 working day for sample ; 5-7 working days for bulk order.

3. Factory direct support : Realeader foucs on Waterproof Connectors for over 13years.

Application of Waterproof Cable Connectors

Shenzhen Realeader Industrial Co.,Ltd , which focus on foreign trade sales and after-sale matters , is an independent wholly-owned company of Shenzhen Dream-Start Electronics Co.,Ltd . Combined with the advantages of research and development , sales and service in Shenzhen Dream-Start , a high-tech private enterprises. Realeader's main products are waterproof plugs , waterproof connectors and circular connectors . The company with independent research and development capabilities , scientific and sound production management system and a wide rang of testing equipment , has passed ISO9001 quality management system.

Adhering to the spirit of continual learning and striving for perfection, the company has developed a variety of waterproof signal connectors , waterproof power connectors , waterproof motor plugs , waterproof mufti-function plugs, "T" type connectors , "Y" type connector , as well as other types of waterproof connectors and circular connectors . The products are widely used in LED lighting lamp , intelligent induction products , household products , new energies , electrical bicycle motor , outdoor appliance , transportation , agricultural machinery and other industrial and fields .

The new product development of Realeader refers to China's national standards "GB/T11918,GB/T11919" and the international standard "IEC60309-1,-2" . The partial products conform to the CCC , CE , UL certification requirements , and several products have applied for national patents . In order to satisfy for various use , we can produce in high temperature-resistant (120℃) or low temperature-resistant (-40℃) , anti-UV , fire-retardant and other special requirements .

Based on market-oriented , our company formulated a long-term strategic plan and development goals, constantly measures ourselves with higher standards and better quality . By constant innovations and improvements , keeping good communication with customers and suppliers , striving to provide safer , more reliable and more stable products ，we ensure that our customers can continue to maintain the advantage in the market competition .

We sincerely look forwarder to working with the board masses of new and old customers sincere cooperation, mutual benefit the industry level and create a better future !